Tab ‘status Tab ‘Status’ 1. When selected the option ‘Formatted text’, the fields ‘Print type’ and ‘Format types’, will be enabled, use the text format styles to test your MP TH printer and get to know the print modes it can perform. Tab ‘tests Open cover sensor: Paper dust congestion, generated by the cutter itself can also cause malfunction. Yellow LED blinking 3 times – Cutter Error Verify if there is paper between the cutter and the mechanism plastic chassis. Exploded View Of The Cover Lever Set The following part numbers are not necessarily available as stand alone units, as they are part of a replacement kit. This manual is intended only for technicians trained by Bematech.

Uploader: Zulkirn
Date Added: 21 October 2004
File Size: 31.84 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 48999
Price: Free* [*Free Regsitration Required]

The next steps are required in order to remove the thermal print head. Page 31 The next steps are required in order to remove the thermal print head.

Hier entsteht was Neues für Sie!

By the end you will have performed a full Removing the Cutter Mechanism, Print Head and Connection Board Beamtec access the printer interior, the cutter mechanism, thermal print head connection board, follow the steps below: Click on the button ‘Update’ and wait for the operation end. After disconnecting the plastic chassis, just pull up the back side to loosen the frontal part. The following part numbers are not necessarily available as stand alone units, tj they are part of a replacement kit.

Test the printer buzzer. Wrong command sequence Verify if the printer command set is properly configured. When selected the option ‘Formatted text’, the fields ‘Print type’ and ‘Format types’, will be enabled, use the text format styles to test your MP TH printer and get to know the mo-4000 modes it can perform. Table Of Contents Summary Introduction Use a soft bristle brush removing all paper dust residues which can accumulate in the cutter mechanism, causing malfunction.

  DX4450 SCAN DRIVER DOWNLOAD

Page 21 – Exploded view of the Control Board Cartr To remove the cutter sensor located at the front of the mechanism pull it to the front while opening the locks that hold the mechanism picture below, on the left.

Page 33 After disconnecting the plastic chassis, just pull up the mp–4000 side to loosen the frontal part. To remove the paper guide, just press it by its base, disconnecting it from the metal chassis as shown on the picture on bematecc right.

Start by removing the sensors and then the cover lock set.

The information may vary from the printer ready status to critical error warnings, which can lead to module replacement to correct a specific issue.

Click on the button ‘Start’ to make a complete test of the printer.

This manual is intended only for technicians trained by Bematech. Page of 55 Go.

Click on the button ‘Get log’ to get a complete report on the printer configuration. Page 25 – Exploded view of the Cutter Mechanism Se The recognition of the interface connected to the control board is done with the reading of a code associated to each kind of board through U2, enabled by the SELDEV signal generated by the control board. Table of Contents Add to my manuals Add.

Bematech Mp Th Fi SM SP Thermal POS Receipt USB Printer | eBay

Page 30 To separate the connection board from the cutter mechanism, start by loosening the screw that holds the grounding cable located on the side of the equipment, then move away the connection board and disconnect the cables.

  EPSON STYLUS NX230 WIRELESS PRINTER DRIVER

With the printer open, paper roll and spacer removed, loosen the two screws on the bdmatec of the Printer, as shown on the right. How this manual is organized Chapter 1 Knowing the product. By pressing tu button you will print only current page. Chapter 4 – less time to replace the paper roll and, therefore, more time available for processing transactions at the retail outlet. Mp-400 remove the printer cover just pull the axle that holds the body case bsmatec one side as shown in the picture on the right.

On the window that was open select the firmware that will be loaded and click on open. After this, just pull it out of the printer cabinet and you will have the complete control board set on your hands. Page 32 To remove the paper guide, just press it kp-4000 its base, disconnecting it from the metal chassis as shown on the picture on the right.

Tab ‘bar Code 1. The option Bitmap allows you to check the graphics printing and the Logo option allows you to test the functions of logo storage and logo printing from volatile and non volatile memories.

Last modified: April 17, 2020